Pneumatic control valve maintenance methods and causes of failure

Pneumatic control valve is widely used in petrochemical companies one of the instruments. It is accurate and normal work to ensure the normal operation of process equipment and safety is of great significance. Therefore, to strengthen the maintenance of pneumatic control valve is necessary. First, check the focus of the inspection site when the body wall: In the high pressure and corrosive media occasions, the valve body wall, diaphragm valve diaphragm often subject to media impact and corrosion, we must focus on inspection of pressure decay; Check Valve seat: medium infiltration due to work, the fixed valve seat thread inner surface vulnerable to corrosion and make the valve seat loose; check the valve: the valve spool is one of the movable parts of the regulating valve, the erosion of the media is more serious, Maintenance should carefully check the various parts of the valve core is corroded, worn, especially in the case of high pressure, valve core wear due to cavitation caused cavitation is more serious. Serious damage to the valve body should be replaced; packing check: Check is dry asbestos rope packing, such as the use of PTFE packing, should check whether the aging and its mating surface is damaged; rubber membrane check whether the actuator is in aging , Whether there is cracking phenomenon. Second, the pneumatic control valve with the routine maintenance When the control valve graphite asbestos as a filler, about three months should be added to the filler on a lubricant to ensure flexible and easy to use control valve. If it is found that the packing pressure cap is very low, it should be filled with filler. If it is found that the PTFE packing is hardened, it should be promptly replaced. Attention should be paid to the operation of the regulating valve during the inspection, check the position indicator and the regulator The output is consistent with; regulator valve positioner should always check the gas source and found the problem promptly handled; should always maintain the health of the valve and the complete and easy-to-use components. Third, the common faults and causes (a) control valve does not move. Symptoms and the reasons are as follows: 1. No signal, no air source. ① gas source is not open, ② due to gas source water in the winter icing, resulting in duct blockage or filter, pressure relief valve plug failure, ③ compressor failure; ④ gas main leakage. 2. Air source, no signal. ① regulator failure, ② signal tube leakage; ③ bellows leak locator; ④ regulate the omentum damage. 3. Locator no air source. ① filter blockage; ② valve failure I ③ pipeline leakage or blockage. 4. Locator has a gas source, no output. The throttle of the positioner is blocked. 5. There is a signal, no action. ① spool off, ② valve core and the community or with the seat stuck; ③ stem bent or broken; ④ seat valve core block or block of dirt; ⑤ actuator spring rust due to long-term useless. (B) control valve instability. Symptoms and causes are as follows: 1. Air pressure instability. ① compressor capacity is too small; ② valve failure. 2. Signal pressure is not stable. ① The time constant of the control system (T = RC) is not appropriate; ② The regulator output is not stable. 3. Gas pressure stability, signal pressure is stable, but the control valve action is still unstable. ① locator amplifier ball valve dirt worn lax, air consumption will increase when the output shock will produce; ② locator amplifier nozzle baffle is not parallel, the baffle cover nozzle; ③ output tube , Line air leakage; ④ actuator stiffness is too small; ⑤ stem friction in the movement of large, with the contact parts of the block phenomenon. (C) regulating valve vibration. Symptoms and causes are as follows: 1. The regulating valve vibrates at any opening. ① unsteady support; ② nearby vibration source; ③ valve core and bush wear serious. 2. Regulating valve in the fully closed position near the vibration. ① control valve selected, often used in a small opening; ② single-seat valve flow direction and closed the opposite direction. (D) regulating valve slow action. The phenomenon of dullness and the reasons are as follows: 1. The stem is only dull when moving in one direction. ① Pneumatic diaphragm actuator diaphragm rupture leakage; ② "O" -type seal leakage in the actuator. 2. Stem in the reciprocating action are slow phenomenon. ① blockage of viscous substances in the valve body; ② polytetrafluoroethylene filler hardening or graphite asbestos filler lubricant drying; ③ filler plus too tight, frictional resistance increases; ④ stem because the valve does not lead to direct friction resistance; ⑤ no Pneumatic positioner valve will lead to slow action. (E) the amount of leakage control valve increases. The reasons for the leakage are as follows: 1. The valve leaks when the valve is fully closed. ① spool is worn, serious leakage, ② valve not adjusted off is not strict. 2. The valve does not reach the fully closed position. ① medium pressure is too large, the actuator rigidity is small, the valve is not strict; ② valve foreign body; ③ bushing sintering. (F) adjustable flow rate smaller. The main reason is that the valve core is corroded and smaller, so that the adjustable minimum flow rate becomes larger. Understand the phenomenon of pneumatic control valve failure and the reasons that symptomatic measures can be taken to resolve.

Transparent Pvc Strip

The purpose of door and window sealing strip Pvc Strip,Transparent Pvc Strip is divided into three categories: glass sealing strip (rubber strip), door leaf and door cover sealing strip and wool strip. The glass sealing strip is used for the sealing between glass and leaf and frame, the door leaf and door cover sealing strip is mainly used for the sealing between door panel and door frame, and the wool strip is mainly used for the sealing between frame and leaf. In the production and installation of plastic steel doors and windows, broken bridge aluminum doors and windows and wooden doors, sealing strip is an essential accessory.

The sealant strip plays an important role in waterproof, sealing and energy saving in plastic steel doors and windows, bridge broken aluminum doors and windows and wooden doors and windows, with sound insulation, dust prevention, antifreeze and warmth preservation. It must have strong tensile strength, good elasticity, and good temperature resistance and aging resistance. In order to ensure the fastening of the rubber strip and the profile, the section structure size of the rubber strip must match the profile of plastic steel doors and windows. Sealant strips are generally used for flat doors and windows, suspended windows and folding doors and windows. The main functions are dust prevention, insect prevention, waterproof, sound insulation, sealing, etc.

The installation position of the wool top is generally on the sliding window (door) leaf, the circumference of the frame leaf or the sealing bridge (wind block) to enhance the sealing between the frame and the leaf. Top specification is an important factor affecting the and watertight performance of push-pull doors and windows, and it is also an important factor affecting the switching force of doors and windows. If the wool top specification is too large or the vertical wool is too high, it will not only make assembly difficult, but also increase the moving resistance of doors and windows, especially the initial resistance when opening and the final positioning resistance when closing. If the specification is too small, or the height of the vertical top is not enough, it is easy to fall out of the groove, which greatly reduces the sealing performance of doors and windows.

There are two kinds of tops: silicified and non silicified. The top after silicified treatment has better effect in use. The appearance of the top with qualified quality is that the surface is straight, the bottom plate and vertical hair are smooth and free of bending, and there are no pits on the bottom plate, which meets the requirements of 0.2mm.

Transparent Pvc Strip,Pvc Strip,Aluminium Sliding Strip,Door And Window Sealing Strip

GuangDong XinCheng Material CO.,LTD , https://www.xin-alu.com