It is most common to install electric floor heating in the cold north, so that in the cold winter, we will not freeze our hands and feet. But most users do not understand the installation of electric floor heating, then, let's understand the installation steps of electric floor heating together, and the precautions for installation of electric floor heating .
1. Installation steps of electric floor heating
1. Before installing the electric floor heater, check the insulation resistance of the cable to see if there is an open circuit or a short circuit. Before installing the cables for floor heating, each one needs to be tested.
2. Start laying thermal insulation board, the ground should be cleaned before laying, the insulation board should be laid neatly, and the gap between each board should not exceed 4mm, which plays the role of thermal insulation.
3. The laying of the floor heating reflective film is generally made of aluminum foil reflective film, which is laid on the insulation board. It should be laid flat and has the effect of transferring heat.
4. The floor heating steel wire net is laid, and each steel wire net needs to be fixed with a cable tie. The role of the steel wire net is mainly to fix the heating cable to prevent the cable from collapsing and changing the position in the later period.
5. Lay the heating cable. When laying the heating cable, recognize the cold and hot wires. The cold wire is connected to the temperature controller and can be cut off. The hot wire is the heating body. It cannot be cut off during the laying. layout.
6. After the heating cable is laid, the insulation resistance and nominal resistance of the electric floor heater need to be tested. Through the test, you can find whether the cable is damaged during the installation of the electric floor heater. If there is a problem, you can replace it in time.
7. When installing the thermostat, you need to determine the location of the thermostat before installing the electric floor heater, and then reserve the wire and the wire box. It is generally installed in a place similar to the position of the light switch, depending on the actual situation. Finally, cement backfilling is needed to protect the finished products and to debug and operate.
2. Matters needing attention in the installation of electric floor heating
1. The floor heating will be laid after the completion of hydropower, then the uneven ground should be leveled. If it is uneven, the heat of the electric floor heating will not be dissipated, affecting the heating effect of the home, and it will also cause excessive power loss and bring economic losses to yourself.
2. The installation of electric floor heating and house decoration are together, so there will be more debris during construction, which will affect the construction work of the construction personnel on the floor heating, and there may be some problems due to improper installation of the electric floor heating. Therefore, the construction environment of electric floor heating is very important.
3. When installing electric floor heating in the bathroom, it is necessary to consider the humidity of the bathroom is relatively large, and it is necessary to do waterproof work. The wall height of the waterproof layer is designed to be 1.8 meters to ensure the waterproof effect of the bathroom. When using it, keep the bathroom clean.
Editor's summary: The above is about the installation steps of electric floor heating , and the precautions for installation of electric floor heating . Friends who don't know much can refer to the above content to learn. Because electric floor heating is indispensable for our decoration, the frequency of use in winter is the highest, so that it can be easily solved during decoration.
What, the decoration still uses his own money? ! The Qi family is decorated in installments, with an ultra-low annual interest rate of 3.55% and a maximum loan of 1 million. Apply now to enjoy the discount
If you are interested in brand cooperation, content cooperation, and advertising of this website, please send an email to :.
Brass knurled thread insert Made of brass material, good thermal conductivity and heat resistance.
Widely Used On the Injection molding for Tightly Fixing.
Brass knurled Can be installed by ultrasonic or heat into thread tapered hole, or molded in during injection.
We are manufacturer of Insert Nut in China, if you want to buy Embedment Insert Nut,Brass Threaded Knurled Insert,Insert Thread Nuts please contact us.
knurled insert nut,threaded insert nut,wood insert nut,brass insert nut,furniture insert nut
Shenzhen Lanejoy Technology Co.,LTD , https://www.ccls-vaccine.com